Printable Version | Subscribe | Add to Favourites
New Topic New Poll New Reply
Author: Subject: Sierra driveshaft hub nut thread direction
FOSSIE

posted on 22/5/24 at 01:14 PM Reply With Quote
Sierra driveshaft hub nut thread direction

Afternoon all,

I just received a pair of new, aftermarket Sierra rear shafts from one of the eBay driveshaft specialists (UK company) and I'm impressed with the quality/service/price etc, however both the nearside and offside shafts have RIGHT hand hub nut threads.

The OE shafts I just removed had a left hand thread on the nearside (as you would expect).

Just wondered if anyone else had come across this, before I go to the bother of trying to return one shaft or enter into a debate?

Is this normal for aftermarket shafts? Is it posible they only manufacture 1 type of CV to keep costs down?

cheers
Tom

View User's Profile View All Posts By User U2U Member
jacko

posted on 22/5/24 at 04:29 PM Reply With Quote
Mine had left hand thread on n/s. And right hand on o/s





555

View User's Profile E-Mail User Visit User's Homepage View All Posts By User U2U Member
voucht
Contributor






Posts 240
Registered 22/5/11
Member Is Offline

Photo Archive Go!
Building: Haynes roadster on the road since november 2014 bu

posted on 22/5/24 at 04:59 PM Reply With Quote
Same here: left hand thread on n/s,and right hand thread on the o/s of my Sierra drive shafts. So it looks like as you say, hey only use one type of CV joint to keep costs down.

Not a problem really if the nut is well secured. For example, on the racing cars I'm working with as a job (Mitjet), we have the same CV joint on the LH and RH driveshafts (right hand thread). But the nut is secured by a nut cage + a pin going through the threaded end of the CV joint. So it can't get off.

I would not trust a nylock nut alone (not secured by a pin) if there is a right hand thread on the nearside drive shaft.

[Edited on 22/5/24 by voucht]





https://vouchtroadster.blogspot.com/
https://cafrazx550.blogspot.com/

View User's Profile E-Mail User Visit User's Homepage View All Posts By User U2U Member
Schrodinger

posted on 22/5/24 at 08:58 PM Reply With Quote
Why don't you ring the suppliers and ask if they should both be rh thread? It could be you have 2 o/s drive shafts or maybe even a mistake o their part.





Keith
Aviemore

View User's Profile E-Mail User View All Posts By User U2U Member
adithorp

posted on 22/5/24 at 09:45 PM Reply With Quote
I had to replace a nearside one just before a trip a few years ago and I could only get a rh threaded one. It's been on ever since without issue (15000miles?). I have had the other (correct one) come loose.

Virtually every other car on the road has a rh threaded joints on both sides and the Sierra one has the highest torque setting of any I've ever come across. I wouldn't worry about it. Mark the nut so you can see if it moves.





"A witty saying proves nothing" Voltaire

http://jpsc.org.uk/forum/

View User's Profile View All Posts By User U2U Member
SteveWalker

posted on 22/5/24 at 10:15 PM Reply With Quote
I did a quick search earlier and found one reference that suggested that early Sierras may have had two right-hand threads.
View User's Profile View All Posts By User U2U Member
christim

posted on 23/5/24 at 11:38 AM Reply With Quote
My aftermarket driveshafts (from J&R) are both RH.
There's a notch in the shafts which apparently allows the nut to be deformed into...but the nuts supplied didn't want to do that (and they're not lock nuts either). I've left it and will check the torque again after xx miles

quote:
Originally posted by adithorp
...Mark the nut so you can see if it moves.

...Also this

(Sierra driveshafts are different lengths so no mistaking a NS for an OS)

[Edited on 23/5/2024 by christim]





My Build Thread

View User's Profile View All Posts By User U2U Member
nick205

posted on 23/5/24 at 12:26 PM Reply With Quote
From experience (built a Ford Sierra based MK Indy) the Ford Sierra N/S and O/S driveshafts are:

1. Slightly different lengths
2. The outer threaded end has a keyway in which you should form a notch from the the hub nut - to prevent them coming undone
3. The torque is high
4. One side is LH thread, the other is RH thread

When I built my Indy I rebuilt the donor driveshafts and fitted new hub nuts.

View User's Profile View All Posts By User U2U Member
motorcycle_mayhem

posted on 23/5/24 at 06:56 PM Reply With Quote
Both the H/D shafts on the race car terminate in RH threads. Both were originally intended for a nut with a deformable external collar, punched into a machined flat. This is discarded and a large castle nut utilised. The end of the shaft is drilled through from the flat to take a roll pin (put the patient in a drill press vice and be careful).
Torqued to 180ft/lb in my case, limited by the bearing restrictions (they're old Fiat spec.)

View User's Profile View All Posts By User U2U Member
tims31

posted on 31/5/24 at 04:52 PM Reply With Quote
Both of mine are right hand threads although they were left and right until I exchanged them when I got my kit.

After a couple of years driving I found one of my wheel bearing was worn as the nut had become undone slightly and allowed play in the bearing. After I changed the bearing I drilled the end of the shaft and wirelocked it to stop any movement. The nuts are only Nyloc and so I wouldn't rely on it and this is a cheap easy fix. Just use a cobalt drill to put a 1.5mm hole in the nut and shaft. Drill slowly with cobalt drill bits.

Description
Description






Build: http://www.martinsfurybuild.co.uk/

View User's Profile Visit User's Homepage View All Posts By User U2U Member

New Topic New Poll New Reply


go to top






Website design and SEO by Studio Montage

All content © 2001-16 LocostBuilders. Reproduction prohibited
Opinions expressed in public posts are those of the author and do not necessarily represent
the views of other users or any member of the LocostBuilders team.
Running XMB 1.8 Partagium [© 2002 XMB Group] on Apache under CentOS Linux
Founded, built and operated by ChrisW.