Evening all

I've always been nervous about crawling under cars on stands etc and would like to invest in something that lifts a car safely.

I've got a 9 foot ceiling in my garage and no chance of raising it (room above) so a two post lift would be no good probably and I doubt I have the width too.

I've looked at the scissor lifts and whilst they don't give the height to be able to stand under the car, they do look a bit more stable than axle stands!

This looks a tidy price - eBay lift

I guess they're a bit of a pain to wind up and down but it's not like I'd be putting cars on and off a lot. Cars tend to spend months (years!) in the air with me!

Any thoughts?

Ta

Wyn

Mk use them and even sell them.

I had one for a while, didn't really work well for my spitfire (backbone chassis, but the lift acted on the sills, so te chassis was hanging off the shell, not ideal) But on teh plus side, I found teh tilting really handy. I had to do some welding to the front of the chassis, and with at full tilt I had loads of space.

I have seen a low manual 4 post lift, that looked handy, not sure if it could be used with a jacking bar.

Big plus of the tilting lift is cost. I got mine "secondhand" but unused. Had it a year, used a few times, so didn't loose any money. (I have returned to my Weber jack and decent axle stands)

I have a scissor lift in my under 8 foot garage and I absolutely HATE it. It is hard to work under and it's structure is always in the way. About the only thing it is good for is changing the tires. Russ

I have this:-

https://i.imgur.com/vMQiHQA.jpg


I have a low roof in the garage but this lift gets the Suttol up to a working height inside.
I've changed an engine in an MX5 by removing the bonnet. Lift and remove the underside stuff,
then lower and lift the engine out with a hydraulic crane.

However, it's portable so can be wheeled out and then will lift 3.5 tonne to 1300mm.
Will lift on chassis, suspension, or use the outriggers and lift by the sills.

Useful tool.

Paul G

[Edited on 12/12/20 by 907]

Hi

I have a 3ton scissor lift in my garage, 9ft ceiling . The lift has a 1m total lift

I have to say it's the best £1500 I have ever spent, it so easy to use, totally reliable and safe, needs a compressed air link to enable the safety stop to be released and ensures if the hydraulics fail it only drops about 50mm

I've had it for about 5 years, it makes things so easy, yes its structure can get in the way a little but it's so much better than faffing around with ramps and jacks etc

It's also mobile and I have used it on the tarred area in front of the garage on occasion, although it does weight about 500kg

Brilliant thing , wouldn't swap it, very similar to this one

https://www.garageequipmentonline.com/products/scissor-lifts/geo-3-tonne-mid-rise-car-scissor-lift

Anyone run post lifts outside?

My brother doing a pre MOT on his old Rover, and yes it did pass.

This is being lifted by the jacking points in the sills.

Paul G


https://i.imgur.com/vBmS3FH.jpg

Mine is used all the time, the tilt function is very handy. I have the adjustable width one set on the narrow width.

Description
Description

quote:

---

Originally posted by lsdweb

I guess they're a bit of a pain to wind up and down but it's not like I'd be putting cars on and off a lot

---

quote:

---

Originally posted by 02GF74

quote:

---

Originally posted by lsdweb

I guess they're a bit of a pain to wind up and down but it's not like I'd be putting cars on and off a lot

---

I'm sure with a bit of ingenuity and the use of a welder, a large bolt or nut can be fixed to the winding mechanism to be turned with a cordless impact driver.

---

quote:

---

Originally posted by cliftyhanger

quote:

---

Originally posted by 02GF74

quote:

---

Originally posted by lsdweb

I guess they're a bit of a pain to wind up and down but it's not like I'd be putting cars on and off a lot

---

I'm sure with a bit of ingenuity and the use of a welder, a large bolt or nut can be fixed to the winding mechanism to be turned with a cordless impact driver.

---

They come with a 1/2" adaptor for a drill. My reasonably powerful cordless would work on slow speed (gearbox) once the car was lifted a bit off the ground, as the geometry means it is hardest with teh jack fully lowered.
A decent mains drill with 2 speeds would work well. I doubt an impact driver would work well, they only create very tiny movements on each impact.

---

Thanks for all the responses.

Some quite mixed views!

The tilt looks useful and scary at the same time - what stops the car sliding off?

Thanks

Wyn

quote:

---

Originally posted by lsdweb
Thanks for all the responses.

Some quite mixed views!

The tilt looks useful and scary at the same time - what stops the car sliding off?

Thanks

Wyn

---

I have a two post lift in my garage, it’s great.

Although I have altered the roof structure to allow full height it mostly gets used with the car at waist height so you can work horizontally rather than down.

It’s a screw lift BTW, fitted new load nuts and a single phase motor with smaller pulley.

Thanks for all the replies! Lots to think about.

The best deal I've seen is this Sealey one - https://www.ebay.co.uk/i/352803793169?mkevt=1&mkcid=28&chn=ps . It can be widened / narrowed which is useful, as I'll have 2 cars going on it probably - Fury and Audi TT. The instructions do say that axle stands must still be used though!

Wyn

[Edited on 18/12/20 by lsdweb]