zetec
|
| posted on 17/1/05 at 07:47 AM |
|
|
Tonneau/boot cover
Anyone had a bash at making a tonneau or boot cover? I was thinking of getting a couple of yards of material and having a go, any advice would be
great. Can a normal sewing machine coop with hood material/vinyl if taken slow? Better to find out now rather than after blowing up my wifes machine.
|
|
|
|
|
Surrey Dave
|
| posted on 17/1/05 at 08:24 AM |
|
|
I made mine in 3 parts , boot cover and 2 tonneau's, it was sewn with an industrial sewing machine I dont think domestic would do , (they have
trouble with my trousers).
I cut the fabric , and then folded and glued the edges , with evostik ,wood and G clamps , then took it to my sewing person to stitch.
 
Rescued attachment sidetonneau1a.jpg
|
|
|
DarrenW
|
| posted on 17/1/05 at 11:02 AM |
|
|
That looks well smart. Can the drivers side cover be removed to leave just the pass side covered when you are driving alone?
|
|
|
Hellfire
|
| posted on 17/1/05 at 01:48 PM |
|
|
Very nice Dave - you state didn't do the sewing then  why's that 
|
|
|
mangogrooveworkshop
|
| posted on 17/1/05 at 05:14 PM |
|
|
Zetec
A modern machine has plastic insides and thats the problem. I used the old singers and that just about gets it done. The industrial machines are the
ones you need. Have you got any sail makers round your way? They do hoods and spray decks for boats which is the same techniques and craftwork. The
local lad here has done a wedge of cars.
[Edited on 17-1-05 by mangogrooveworkshop]
|
|
|
zetec
|
| posted on 17/1/05 at 05:25 PM |
|
|
Thanks everyone, Dave that is a top notch job ! just the sort of thing I want.
You say you turned the edges and glued them, did you then just get them stiched to secure better? Also what material did you use?
Once again nice job!
|
|
|
Surrey Dave
|
| posted on 17/1/05 at 05:34 PM |
|
|
Yes you can just remove the drivers side , it's pretty cosy!!, especially with the 'Flintstones hood up as well and the sidescreens on.
Zetec: I dont think the glue would hold it for long, but it saved the sewist(?) worrying about the measurments...
The Vinyl came from ' Woolies ' I think....
Hellfire: I didnt have a tough enough sewing machine, the one I use for my curtains wouldn't handle it
Us 'Southern Soft Twats' can do anything!!
[Edited on 17/1/05 by Surrey Dave]
|
|
|
albertz
|
| posted on 18/1/05 at 09:41 PM |
|
|
Thats a nice arrangement, i'll be happy with a boot cover half as good looking as that.
Could i ask what kind of fasteners you have used and where you got them from?
|
|
|
Surrey Dave
|
| posted on 22/1/05 at 12:42 PM |
|
|
i call them poppers but I'm not sure if thats the real name!
They came from 'Woolies' , and you need a little anvil and punch to fit them.
I used a few 'lift the dot' fasteners in crucial areas.
|
|
|
zetec
|
| posted on 22/1/05 at 04:33 PM |
|
|
Got a quote today from a firm to do a set as per Dave's car £225.
Looks a bit high, suspect materials would cost about £50 (zip, fixings, vinyl etc) so £175 labour...
Anyone else had one made, and if so what price?
" I only registered to look at the pictures, now I'm stuck with this username for the rest of my life!"
|
|
|
Surrey Dave
|
| posted on 22/1/05 at 05:37 PM |
|
|
Zetec: You are welcome try my tonneau's ,and boot cover on your car.
The tonneau's apart from working out the shape are not very difficult , just flat vinyl with an 1" or so turn up round the edge.
I have no centre zip ,just a healthy overlap.
The rear cover was a bit more trial and error ,but even if it did not fit your car it may be near enough to make a pattern from.
|
|
|
zetec
|
| posted on 23/1/05 at 11:41 AM |
|
|
Thanks Dave.
" I only registered to look at the pictures, now I'm stuck with this username for the rest of my life!"
|
|
|
