Printable Version | Subscribe | Add to Favourites
New Topic New Poll New Reply
Author: Subject: Working on body work, plus flip nose.
derf

posted on 1/6/04 at 01:37 PM Reply With Quote
Working on body work, plus flip nose.

I had a bunch of free time over the weekend, and got working on properly mounting the body, still need to actually mount the bodywork, but at this point in time it fits on the body. I made the nose flip forward with a pair of hinges. The only problem I see now is that the engine will not clear the hood, I have less than 1/4 inch of protrusion of the intake where the hood will sit.

Flip forward nose
Flip forward nose

Overview
Overview

View User's Profile View All Posts By User U2U Member
stephen_gusterson

posted on 1/6/04 at 01:46 PM Reply With Quote
looking good

wish i had that amount of room to work in

is that a rotary engine?

did you tell us what your job was in the other thread?

cheers


steve

[Edited on 1/6/04 by stephen_gusterson]






View User's Profile E-Mail User View All Posts By User U2U Member
derf

posted on 1/6/04 at 02:52 PM Reply With Quote
Yes just did it. No it isnt really as much room as it looks, I share that space with 3 other people, plus the whole area on the left, bottom right, and far (out of photo) has to be open so the utilities folks can read their meters. Plus when I'm done building I still have to figure out how to get the car out of the basement, and up a flight of stairs that it wont turn into. Yes it is a 13b
View User's Profile View All Posts By User U2U Member
TPG

posted on 1/6/04 at 07:32 PM Reply With Quote
Will the nose hit the ground before being fully open once its at its correct ride hieght/sat on its wheels?Nice idea though





..Which was nice..

View User's Profile View All Posts By User U2U Member
JoelP

posted on 1/6/04 at 08:27 PM Reply With Quote
mines done exactly like that, it is flat on the ground when opened at ride height. might end up scratched if im not careful!






View User's Profile View All Posts By User U2U Member
derf

posted on 2/6/04 at 11:58 AM Reply With Quote
I'm going to eventually put in some tyype of spring or steel rope to keep it from opening fully. The only thing about steel rope is Tht I'm scared it will get caught in moving engine parts, and I dont know if I want a spring that could stretch farther than I really want it to.
View User's Profile View All Posts By User U2U Member
pbura

posted on 2/6/04 at 02:22 PM Reply With Quote
How about a check strap at the hinged joint?

Pete





Pete

View User's Profile E-Mail User View All Posts By User U2U Member
derf

posted on 2/6/04 at 04:31 PM Reply With Quote
That would prolly work, like a leather strap that will only go so far
View User's Profile View All Posts By User U2U Member
pbura

posted on 2/6/04 at 06:32 PM Reply With Quote
The hinged front's a good idea, will have to tuck it away to copy

So how are you going to handle the engine clearance? Can you lower the engine a little?

Just curious, how much lower is the sump than the chassis right now?





Pete

View User's Profile E-Mail User View All Posts By User U2U Member
derf

posted on 2/6/04 at 07:36 PM Reply With Quote
The sump is lower than it should be. I think it is actually about 1 1/4inches down. I was expecting to have to make a hood scoop, after seeing photos of other 13b locosts, all the engines came up above the hoodline. I have been planing from the begining to make a hood scoop, most likely out of aluminum, and I'll just weld it in, grind down the welds, and paint.
View User's Profile View All Posts By User U2U Member
robinbastd

posted on 2/6/04 at 08:29 PM Reply With Quote
Why not use an inertia reel seat belt as the retaining strap for the bonnet?
Ian





Only a dead fish swims with the tide.

http://smuttygifts.com/

View User's Profile Visit User's Homepage View All Posts By User U2U Member
nicklondon

posted on 3/6/04 at 08:11 AM Reply With Quote
if you fitted lift off hinges you could remove the nose completely.
View User's Profile View All Posts By User U2U Member
zilspeed

posted on 3/6/04 at 08:18 AM Reply With Quote
quote:
Originally posted by derf
. I have been planing from the begining to make a hood scoop, most likely out of aluminum, and I'll just weld it in, grind down the welds, and paint.


That's aluminium young man.
Not-A-loo-min-um ;-)

Cheeky wee anglo - american gag there...






View User's Profile E-Mail User View All Posts By User U2U Member
derf

posted on 3/6/04 at 01:07 PM Reply With Quote
first off it's a hood, not a bonnet, baby girls wear bonnets. and it's aluminum (alluhhmin eeum
View User's Profile View All Posts By User U2U Member
Steve&Steve

posted on 4/6/04 at 07:40 AM Reply With Quote
Damp

Derf, I am also planning on building my chassis in the basement of my house. I have been quite worried about damp being a issue.

In your pictures damp can be clearly seen around the edges of the room and even in the middle of the floor under the chassis. Has this caused you much of a problem? Also surface corrosion can be seen on your metalwork, how long has it taken to get like that, and is it really a problem?

My basement looks less damp than yours, though there is about an inch of damp visible in the corners bye the walls and the air does smell a little musty. I have a household dehumidifier I will be using but am still worried about the damp affecting the chassis and especially the risk of wooden base board warping during the early stages of chassis construction.

All comments/ideas welcome, cheers Steve

View User's Profile View All Posts By User U2U Member
derf

posted on 4/6/04 at 12:49 PM Reply With Quote
Yes the basement is very damp. I dont own a house, and rent an appartment. I use the basement of another building, so I really cant use power tools down there either (except when the people above me are not home).

When it rains the walls leak, when it floods the doorleaks, when they run their sink a pipe leaks, when they flush the toilet a ppe leaks, when no-one is doing anything a something leaks.

There are some wet spots in the basement, the one behind the car is a 2 inch deep puddle, the one to the right is hot water, far right is cold water to the toilet, behind and to the right is rain water.....

There is some surface rust on the chassis, no pitting yet, if somewhere looks like it will be bad then I just rub it with some sandpaper. I cant paint the car down ther because people live above my work area, and I cant just take the chassis from the basement whenever I feel, I would need to cut it in 1/2 to get it out. For that reason I havnt welded the middle of the chassis yet. When I do take the chassis from the basement, after I add suspension, and buy aluminum for the body, then I can take the chassis outside, sandblast it, and paint it, andd finish building it in my parking lot.

View User's Profile View All Posts By User U2U Member
sgraber

posted on 4/6/04 at 08:13 PM Reply With Quote
Thought about waterproofing the bottom and turning it into a boat?

Really though Fred - it looks good, and if you can build under those conditions, you are a very dedicated person!

You should coat the frame with Rust Bullet. It works fantastic.

Graber





Steve Graber
http://www.grabercars.com/

"Quickness through lightness"

View User's Profile E-Mail User Visit User's Homepage View All Posts By User U2U Member
flak monkey

posted on 4/6/04 at 08:23 PM Reply With Quote
quote:
Originally posted by zilspeed
quote:
Originally posted by derf
. I have been planing from the begining to make a hood scoop, most likely out of aluminum, and I'll just weld it in, grind down the welds, and paint.


That's aluminium young man.
Not-A-loo-min-um ;-)

Cheeky wee anglo - american gag there...



If you want a useless fact...(I'm full of them..)

ALUMINIUM, was originally called ALUMINUM.

Evidently this doesnt fit in with the pattern of naming in the periodic table. So the Brits/Europeans changed it to ALUMINIUM, to follow on from strontium, Gallium, Indium, etc that are in the same group as aluminium.

The Brits chanegd it, and the Americans didnt want to. So we are stuck with the double naming....

Told you it was useless!

Cheers,
David





Sera

http://www.motosera.com

View User's Profile Visit User's Homepage View All Posts By User U2U Member
derf

posted on 5/6/04 at 12:12 AM Reply With Quote
Aluminium aluminum, who gives a pahtoot?
View User's Profile View All Posts By User U2U Member

New Topic New Poll New Reply


go to top






Website design and SEO by Studio Montage

All content © 2001-16 LocostBuilders. Reproduction prohibited
Opinions expressed in public posts are those of the author and do not necessarily represent
the views of other users or any member of the LocostBuilders team.
Running XMB 1.8 Partagium [© 2002 XMB Group] on Apache under CentOS Linux
Founded, built and operated by ChrisW.