beaver34
|
| posted on 9/12/15 at 05:04 PM |
|
|
trans tunnel panel trim
hi,
after redoing my transmission tunnel in carbon sheet that i have spare.
what do people use for edging trim looking for 90 degree maybe 1mm alloy of something like that?
|
|
|
|
|
loggyboy
|
| posted on 9/12/15 at 06:22 PM |
|
|
Ally Cope moulding is common, but usually thicker (2-3mm) and about 20x5mm.
http://www.clickmetal.co.uk/Angle-Types/Mouldings/Aluminium-Cope-Mouldings/p-16-8-16/
Mistral Motorsport
|
|
|
chicade
|
| posted on 9/12/15 at 07:56 PM |
|
|
Just out of curiosity where did you get your carbon sheet for the tunnel top? And is it real carbon or carbon effect? Looking to do the same in my mk
indy
|
|
|
twybrow
|
| posted on 9/12/15 at 08:06 PM |
|
|
I think I have spare J profile Ali extrusion in the garage. I am away until the weekend, but if you can wait, I will check what I have....?
|
|
|
Toys2
|
| posted on 9/12/15 at 08:48 PM |
|
|
I thought that this was a clever solution
From
http://www.locostbuilders.co.uk/forum/50/viewthread.php?tid=194553&page=10
http://s133.photobucket.com/user/corsaboss/media/October%2015/1799FBB7-4452-4035-BCD1-83162012AB35.jpg.html
http://s133.photobucket.com/user/corsaboss/media/October%2015/111E4AB9-A69E-435E-A455-1A49103DCE3D.jpg.html
[Edited on 9/12/15 by Toys2]
[Edited on 9/12/15 by Toys2]
|
|
|
beaver34
|
| posted on 10/12/15 at 07:23 AM |
|
|
quote:
Originally posted by twybrow
I think I have spare J profile Ali extrusion in the garage. I am away until the weekend, but if you can wait, I will check what I have....?
yes no rush
thank you
|
|
|
beaver34
|
| posted on 10/12/15 at 07:26 AM |
|
|
quote:
Originally posted by Toys2
I thought that this was a clever solution
From
http://www.locostbuilders.co.uk/forum/50/viewthread.php?tid=194553&page=10
http://s133.photobucket.com/user/corsaboss/media/October%2015/1799FBB7-4452-4035-BCD1-83162012AB35.jpg.html
http://s133.photobucket.com/user/corsaboss/media/October%2015/111E4AB9-A69E-435E-A455-1A49103DCE3D.jpg.html
[Edited on 9/12/15 by Toys2]
[Edited on 9/12/15 by Toys2]
looks smart, id be happy with that, ill have a look online for some of that
next question gear shift gaitors, i need one of them, what have people done there, im using a quaife type 9 shifter its quite short
|
|
|
renetom
|
| posted on 10/12/15 at 08:45 AM |
|
|
Trim
Hi
We used kitchen worktop end trims
They have a nice radiused edge & you can use them
either way, wide section to top or sides
 
Interior trim
Good luck
[Edited on 10/12/15 by renetom]
|
|
|
