Rescued attachment Pair high side smoothy seat side view.jpg
Hi triton,
can you put up some pics of your narrow seats and give me the prices. Small car and I aint a lardy.
Measurements would be good too.
What is postage to Glasgow gonna be?
Seats are 390mm wide, 830mm from floor to top of headrest and the canny bit is they are £195.00 inc postage to Glasgow.
Rescued attachment Pair high side smoothy seat side view.jpg
Hi Triton
If its one like these in the photo then next Friday would be great!
Let me know how you want paying, Paypal OK
Cheers
Simes
Sime43,
Yes I can get one of the above to you for next friday....paypal tickety boo with me.
I have u2u'd you by the way.
Cheers
Mark
Are they 195 each or per pair??
Sorry for being dumb...
Now worries mate i have "senior moments" everyday just recently.
Price is for a pair...mad i know but hey!
Mark
do they fit into a tiger avon do you know?
What about runners / fixing points?
cheers
Yes they fit the Avon, Lightning on the forum has some in his car ....Exeter if i remember right or at least close to it.
Mark
Thread hijack.
Triton, you know ive asked this before, but so much going on in my head at the moment ive forgot. Do those seats fit the Mad Mini, and also now the
daft bit. Will they go flexi as they will be QUITE close to my engine.
Rescued attachment Pictures30.04.05 006.jpg
You will need to create a heat shield anyway as that little beast will cook you alive...
I can use high temp resin if you fancied paying a quid or so more to feel safer
Mark
How much more?. How easy would it be for you to make the back of the seats smooth too.
( are the seats like mk's by the way)
quote:
Originally posted by welderman
How much more?. How easy would it be for you to make the back of the seats smooth too.
( are the seats like mk's by the way)
So it's the low sided ones which are suited for the Mad Mini. The ones without hole in bottom. Think they will look and feel ok when ive got the
harness on.
[Edited on 26/1/06 by welderman]Image deleted by owner
Depends on you but yes either the narrow one on the left or the wider one on the right.
Trying to climb into a high sided seat thru a door will be painfull i think...edge of seat going somewhere perhaps...
Ok then, i have mk seats, so which one is the closest for like for like. ie my bum etc fits ok in what i have in my indy.
Left hand one...(the narrow ones) and cheap as chips at only £190 per pair inc postie's bit.
Mark
quote:
Originally posted by Triton
Left hand one...(the narrow ones) and cheap as chips at only £190 per pair inc postie's bit.
Mark
what was the answer to the fixing question? side or bottom.
cheers
Rear seats don't quite match though.
Side or base mount available and both use steel M8 inserts bonded into base section.
Cheers
Mark
Just realised that the Mad Mini will have door bars, so may get away with the belt holes in the seats. Same price Triton?.
Welderbloke,
Yes low side and high side narrow jobbies are same price.
low sides not as low as you think though still hold you in, just makes it easier to fit the belts as they go over rather than through the seat.
Always go for the wizardy hat ones
Mark
u2u
Indeedly you did
So how do i pay?
Triton i want some aswell have sent you u2u
Welder-bloke and Dax- bloke sent you u2u's
Triton can i pay with paypal so we can get the ball rolling sent another u2u
u2u returned and paypal no problem to my email address.
Cheers
Mark
Triton u2u and paypal sent.
Many thanks
Get back in your shed Triton,there are 24 hours in a day.
Oy, wait your turn lads !!