mr henderson
|
| posted on 9/12/09 at 10:25 PM |
|
|
Fabricated front upright, anyone made one?
The topic of uprights crops up a lot, quite often in a 'which is the least unsuitable for my build?' type of way.
So I wonder if anyone has had a go at making their own?
|
|
|
|
|
MakeEverything
|
| posted on 9/12/09 at 10:30 PM |
|
|
Was going to in acccordance with the Rorty drawings, but never bothered as i picked up some proper used sierra ones for £30.
Kindest Regards,
Richard.
...You can make it foolProof, but youll never make it Idiot Proof!...
|
|
|
liam.mccaffrey
|
| posted on 9/12/09 at 10:36 PM |
|
|
MNR were working on one, I took this pic at Total Kit car Live in 06???
Build Blog
Build Photo Album
|
|
|
mangogrooveworkshop
|
| posted on 9/12/09 at 10:40 PM |
|
|
martin motorleria made his own
|
|
|
JoelP
|
| posted on 9/12/09 at 10:45 PM |
|
|
liam pictures the raceleda one, which i believe MNR have now stopped making, though i may be wrong.
|
|
|
snakebelly
|
| posted on 10/12/09 at 09:10 AM |
|
|
that picture isnt the raceleda one, the raceleda one is a one piece casting that one is fabricated
|
|
|
welderman
|
| posted on 10/12/09 at 10:07 AM |
|
|
this is my attempt, does it work ?. i will have to see, lol.
 
Rescued attachment 301120091213.jpg
Thank's, Joe 
I don't stalk people
http://www.locostbuilders.co.uk/forum/23/viewthread.php?tid=172301
Back on with the Fisher Fury R1
|
|
|
SPYDER
|
| posted on 10/12/09 at 10:18 AM |
|
|
Hi there. Picture below shows the fabricated upright design on our Phoenix. It is basically made from two intersecting tubes. But there's the
rub. The angles have to be spot on. A jig will almost certainly be required. In your case I guess you would have to mimic sierra geometry so there is
the start point for a jig.
This level of fabrication isn't easy, that's why you don't often see fabricated uprights, particularly DIY ones.
If you do take the project on make sure that you enlist the services of a good welder.
Before you ask, no, we didn't make these ourselves, they came from Stuart Taylor Motorsport, albeit in un-finished form. We had to sort out the
steering arms. They weren't welded by Eldon, either. His welding is loads better!
Geoff & Eldon.
[img] [/img]
|
|
|
turbodisplay
|
| posted on 10/12/09 at 10:20 AM |
|
|
If you wer to use the 2 intersecting tubes as above, i would get laser cut tube, so it was spot on.
Darren
|
NOTE:This user is registered as a LocostBuilders trader and may offer commercial services to other users
|
flak monkey
|
| posted on 10/12/09 at 08:53 PM |
|
|
I designed some a while back, but never released the drawings for safety reasons.
For long term safety they ideally need stress relieving.
Plus they are also very dependant on the welders competance.
Sera
http://www.motosera.com
|
|
|
MikeRJ
|
| posted on 10/12/09 at 10:34 PM |
|
|
IIRC Rortys design used interlocking parts to ensure a decent level of accuracy of the assembled item (though it will still distort after welding I
guess).
|
|
|
