Board logo

Any CBR919 near SN13 area?
fullpint - 5/2/12 at 05:37 PM

I'm after a peek at your chole set-up. I had a member give me a choke cable and I also purchased a mini type cable so that one day I can run it thru into the dash.
However my problem is; When I pull the choke cable every thing works fine and the engine starts on the button first time. The ONLY way to turn the choke off is to manual push the choke rod plate back towards the bulkhead. Question is should there be some sort of return spring to aid the return of the choke rod plate

Dangle_kt - 5/2/12 at 06:04 PM

I don't have my car anymore, but the choke plate was spring loaded on mine, had to keep it pushed on with my finger or it the choke would switch off.

I always intended fittin the choke cable I had, but never got round to it.

mark chandler - 5/2/12 at 06:19 PM

On the choke bracket on the carbs they should be a spring like you find in a click top pen, this sits at the end of the mechanism on a couple of lugs.

Regards Mark

fullpint - 5/2/12 at 06:31 PM

Hi Mark; That sounds like what I should have!!
Just took a pic, if you have a look I presume the pen like springs (4 off??) fit into the gap. 3 being the same size and one needed to be a bit longer!!
Description
Description

mark chandler - 5/2/12 at 07:05 PM

That's it, spring goes under the slide on that lug

fullpint - 5/2/12 at 07:16 PM

Will drop an email to David Silver to see if they have a set in stock.. Cheers;

tony.g - 5/2/12 at 07:19 PM

Check this diagram out I think it's no 10
I will try and take a photo of mine later.
http://www.hondaoriginalparts.com/honda_motorcycle_parts_selection_pfk.php?block_01=13MW0N41&block_02=E__1800&block_03=1158

fullpint - 5/2/12 at 07:31 PM

quote:
Originally posted by tony.g
Check this diagram out I think it's no 10
I will try and take a photo of mine later.
http://www.hondaoriginalparts.com/honda_motorcycle_parts_selection_pfk.php?block_01=13MW0N41&block_02=E__1800&block_03=1158

That would be good mate. So it's only 2 springs that are needed?

Proby - 5/2/12 at 08:59 PM

Off the top of my head, I think there is only one spring, at the one end. Will take a pic and post it tomorrow if needed.

tony.g - 5/2/12 at 10:01 PM

There is only a spring on my rear carb, and there is a photo in my photo archive.
I don't know how to put it on this page.
I hope this helps.

Tony

Chippy - 5/2/12 at 11:02 PM

This one? Cheers Ray
[img] choke spring
choke spring [/img]

fullpint - 6/2/12 at 06:14 AM

Cheers all, makes me wonder why mine was taken off!! Or may be the previous owner(s) didnt feel the need to carry the extra weight

brookie - 6/2/12 at 04:31 PM

i got the 919 and dont have one fitted at all

fullpint - 6/2/12 at 05:14 PM

quote:
Originally posted by brookie
i got the 919 and dont have one fitted at all

How do you get on with a cold start?
Ok David Silver have come back but it's not clear how many compression springs are needed. That diagram shows item number 10 (2 off) and also number 9.. Also want £4 each for a sprng

brookie - 7/2/12 at 04:18 PM

i dont in the winter but spring and summer fine