evo.rocks
|
| posted on 23/6/09 at 08:48 AM |
|
|
Exhaust pipe fabrication???
Hi,
I need a new exhaust pipe making which links my manifold to the end can. As you can see from the picture it is just a straight pipe about 1meter long
which is a little wider at the manifold end so it can slide over and a exhausr clip can secure it on
Can anyone make these or do you no anyone that can? Also what price would i be looking at?
|
|
|
|
|
nib1980
|
| posted on 23/6/09 at 08:54 AM |
|
|
try contacting 907 on here I'm sure he'll be able to help you
|
|
|
twybrow
|
| posted on 23/6/09 at 09:03 AM |
|
|
PipeWerx- they will even flare the end for free for you. Very
helpful guys when I spoke to them....
[Edited on 23/6/09 by twybrow]
|
|
|
blakep82
|
| posted on 23/6/09 at 09:28 AM |
|
|
do you just need something like this?
http://www.merlinmotorsport.co.uk/p10921/JETEX-STRAIGHT-TUBE-STAINLESS-1-METRE-2%22/product_info.html
________________________
IVA manual link http://www.businesslink.gov.uk/bdotg/action/detail?type=RESOURCES&itemId=1081997083
don't write OT on a new thread title, you're creating the topic, everything you write is very much ON topic!
|
|
|
welderman
|
| posted on 23/6/09 at 10:35 AM |
|
|
i should be able to sort you out, what are the sizes you require, ie, maifold end, either slip on or slip in. Can end same on or in, dims in mm
please.
Joe
one i made for some one off here
 
Rescued attachment 8Image023.jpg
Thank's, Joe 
I don't stalk people
http://www.locostbuilders.co.uk/forum/23/viewthread.php?tid=172301
Back on with the Fisher Fury R1
|
|
|
evo.rocks
|
| posted on 23/6/09 at 10:38 AM |
|
|
yes thats what i need something like that. Now i just need a welder, anyone now any welders in the warrington area?
|
|
|
welderman
|
| posted on 23/6/09 at 10:41 AM |
|
|
you dont need a welder if its going to slip on/in mate.
can the car be drive ?. If so im near Chorley
Joe
Thank's, Joe
I don't stalk people
http://www.locostbuilders.co.uk/forum/23/viewthread.php?tid=172301
Back on with the Fisher Fury R1
|
|
|
evo.rocks
|
| posted on 23/6/09 at 10:47 AM |
|
|
i would prefere somebody else to di it though, make the pipe for me that is.
Welderman, how much would you charge for a 1mtr straight pipe with different diameter ends?
I am not sure of the sizes as i am just after a price at the minute?
Thanks
|
|
|
evo.rocks
|
| posted on 23/6/09 at 10:54 AM |
|
|
well yes i can take the exhaust pipe off i have at the minute and bring my new viper race can, when i buy it that is, and you can make up me a link
pipe if thats ok?
What finish can you give me on the pipe? stainless steel, titanium, etc? and most importantly how much?
|
|
|
imp paul
|
| posted on 23/6/09 at 01:33 PM |
|
|
joe is the man for the job hi joe hope your ok all the best paul
|
|
|
welderman
|
| posted on 5/7/09 at 08:31 PM |
|
|
Hi Paul, ye not too bad, had to have a week off work so far. Had a little op so been laid up, back to hospital tomorrow and hope to get thumbs up to
go back to work
Joe
Thank's, Joe
I don't stalk people
http://www.locostbuilders.co.uk/forum/23/viewthread.php?tid=172301
Back on with the Fisher Fury R1
|
|
|
.JPG)
